If your Aqua Rite salt reading is too high, it’s important to take action to correct the problem. If you think this might be the case, you should contact your local service technician for further assistance. The last reason why your Aqua Rite salt reading might not be accurate is because of a problem with the control board. This can happen if you have recently added salt to the pool or if evaporation has occurred. Another reason could be that the electrolyte level in the pool is too low. The first reason could be that the sensors are dirty and need to be cleaned. If your Aqua Rite salt reading is not accurate, it could be for a few different reasons. Turn on the power and let the salt cell run for 24 hours before adding it back into the pool. Rinse the salt cell again with fresh water and reattach it to the power source.ĥ. This will help to remove any build-up on the electrodes.Ĥ. Soak the salt cell in a solution of one part vinegar to ten parts water for 30 minutes. Rinse the salt cell with fresh water to remove any residual chlorine or other chemicals.ģ. Remove the salt cell from the pool and disconnect it from the power source.Ģ. The process is actually quite simple and only takes a few minutes. If you have a Hayward salt cell, you may be wondering how to reset it after cleaning. How to Reset Hayward Salt Cell After Cleaning How To: Recalibrate the Salt Level on a Hayward Aqua Rite The display should now read “0.” If it does not, repeat steps 4-5 until it does.ĦNow, slowly turn both trimpots counterclockwise until the display reads “-3.”Īgain, do not force them beyond this point or you may damage the control board. Reconnect the power supply and turn on the unit. Use a small screwdriver to turn both trimpots clockwise until they stop. Locate the two trimpots on the control board labeled “R” and “C.” These are the calibration pots.Ĥ. Take off the front panel of the unit and remove the control board.ģ. Remove the power supply from the unit and disconnect any wires.Ģ. If your Hayward Aqua Rite salt chlorinator isn’t working properly, it may need to be recalibrated. How Do You Recalibrate Hayward Aqua Rite? Rinse well and dry completely.Ĥ.Replace the salt cell in the generator and turn on the power. To do this, follow these steps:ġ.Turn off the power to the pool salt generator.Ģ.Remove the salt cell from the generator.ģ.Clean the salt cell with a soft brush and soapy water. If your pool salt generator is not working properly, you may need to reset it. These parts can be found at most pool supply stores or online retailers that sell pool equipment. This includes things like O-rings, gaskets, and seals. The amount of salt needed will vary depending on how large your unit is, but you should add enough so that there is a layer of salt about 1 inch thick over the entire surface area ofthe electrodes inside your Aqua Plus unit.ĥ) Replace any parts that may have worn out or been damaged during use. This can be done by removing the plug at the bottom of the unit and letting all of the water drain out.īe sure to use clean, potable water when refilliing your Aqua Plus unit.Ĥ) Add salt to the unit. This can be done by either unplugging it from the wall outlet or by disconnecting the batteries.Ģ) Drain all of the water out of the unit. There are a few steps that need to be followed in order to reset the Hayward Aqua Plus system:ġ) Remove the power supply from the unit. Over time, the Aqua Plus system can become less effective, and may need to be reset in order to work properly again. The chlorine is then used to sanitize the pool water. Hayward’s Aqua Plus is a saltwater chlorination system that uses electrolysis to produce chlorine from salt. How Do I Reset My Hayward Aqua Plus Salt System? The unit should now be reset and working properly. Replace the control panel cover and reconnect the power supply. Use a small screwdriver or other pointed object to press and hold the reset button for about 15 seconds.Ĥ. Remove the control panel cover and locate the reset button on the circuit board.ģ. Disconnect the power supply to the unit.Ģ. If your Hayward Aqua Rite salt chlorine generator isn’t working properly, you may need to reset it. How Do I Reset My Hayward Aqua Rite Salt Chlorine Generator? Hayward Salt Cell Not Reading Salt Level Correctly.How to Reset Hayward Salt Cell After Cleaning.How To: Recalibrate the Salt Level on a Hayward Aqua Rite.How Do You Recalibrate Hayward Aqua Rite?.How Do I Reset My Hayward Aqua Plus Salt System?. How Do I Reset My Hayward Aqua Rite Salt Chlorine Generator?.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |